DIY     OBD-II Codes     Fix your Car     Repair Manuals     -Forum-

Advertisement  [ ? ]

Site Links

Parking Brake Service


When doing a brake job, always check to make sure the parking brake is operating properly.

The next time you are doing a brake job, don't forget to check the parking brake. Though most motorists seldom use their parking brakes, it is a required safety device and must work properly when called upon to keep a vehicle stationary.

The main function of the parking brake is to prevent the vehicle from rolling when it is parked. But PARK serves the same purpose in vehicles with automatic transmissions, as does leaving a manual transmission in gear. So to many people, the parking brake seems unnecessarily redundant. Even so, it should be used at least occasionally.

When the parking brake is seldom used, one of two things can happen: it may stick and not release when applied, or it may allow brake pedal travel to increase.

Using the parking brake helps keep the cables freed up so corrosion can't buildup and cause the cables to bind. Applying the parking brake also works the self-adjusters in the rear brakes and helps keep the linings in drum brakes properly adjusted for minimum pedal travel. On cars with four wheel disc brakes and locking rear calipers, using the parking brake keeps the threaded self-adjusting mechanisms inside the rear caliper pistons working freely to compensate for pad wear.

The parking brake also has a secondary purpose. It is also an emergency brake. Should both hydraulic circuits fail, the driver can always yank on the parking brake to slow the vehicle down. The stopping power provided by the rear brakes is marginal, but better than nothing.

The parking brake system is pretty simple. On vehicles with rear drum brakes, applying the parking brake pulls a pair of cables that are attached to arms on the secondary brake shoes. This forces both pairs of shoes outward against the drums to lock the brakes. On four wheel disc brake applications, the disc brake pads are pushed against the rotor by the caliper pistons. This requires either a cam or screw mechanism inside the caliper piston that pushes the piston out and holds it there, or a mini-drum brake inside the rear rotor.

On rear disc brake applications with locking calipers, the adjustment of the parking brake cable is especially important. If the cable is adjusted too tight, there may not be sufficient travel to work the self-adjusters and/or the brakes may drag. If the cable is adjusted too loose, the parking brake may not hold the vehicle. As a rule, most hand levers should travel only about four or five "clicks" when properly adjusted.

On rear disc brake applications with mini-drums in the rotors, the parking brake works like a conventional duo-servo drum parking brake. Pulling the cable forces the shoes outward against the drum to lock the wheel. But unlike a full-sized drum brake, there is no self-adjuster mechanism for the star wheel to compensate for shoe wear. The only time the parking brake is applied is when the vehicle is at rest, so the shoes should last the life of the vehicle unless the parking brake is not releasing causing the shoes to drag. The thickness of the shoe linings doesn't really matter as long as there is enough lining left to hold the car on an incline with normal cable travel.

On most vehicles, the left and right parking brake cables come together and are attached to a lever linkage called an "equalizer" yoke under the vehicle. The equalizer yoke balances, or equalizes, the amount of force that is applied to both cables when the parking brake is applied. The equalizer linkage, in turn, is connected to a single cable that runs to the parking brake lever or pedal. An adjustment screw may be located on the front cable where it connects to the equalizer, or where the cable attaches to the parking brake lever.

emergency brake, parking brake
Rust is the main concern with the brake cables and linkage. Rust can cause the cables to bind in their sheaths, preventing the brakes from being applied or released. If one cable freezes up, the equalizer can't do its job and only one wheel will lock. Though this may not create a problem when the parking brake is used for parking, it could create a serious brake imbalance should the system ever be called upon for emergency braking. The imbalance would likely cause one wheel to lock up and skid, throwing the vehicle into a spin.

The equalizer linkage can also rust up, interfering with proper application and release. Also inspect the hinge pivot because it can break loose, rendering the parking brake useless.

When doing a brake job, therefore, always check the operation of both parking brake cables and the equalizer linkage. Apply the parking brake to see if the linkage is working properly and that the brakes will hold the vehicle. Then check to see that the brakes release fully. If there is any binding and/or corrosion, clean and lubricate the cables (if possible) with brake grease, or replace the cables. Also lubricate the pivot point on the equalizer linkage.

Watch Out for Late Model Import Vehicles with Electric Parking Brakes

A growing number of import (and soon to be domestic) vehicles are now equipped with electronic parking brakes that automatically lock the rear wheels when the transmission is shifted into park. The caliper has a small electric motor that squeezes the brake pads against the brake rotor. Applications include Audi, BMW, Mercedes and VW.

If you are doing a brake job on one of these vehicles, you need a factory scan tool or an aftermarket scan tool to back off and release the electric calipers.Electronic Parking Brake scan tool
Mac Tools has recently introduced an "Electronic Parking Brake Service Tool" that can disengage the park brake as well as read and clean electronic parking brake fault codes. The EPB101 tool is plugged into the vehicle OBD II diagnostic connector under the instrument panel. The tool then communicates with the control module to diagnose and service the electronic parking brake system. Functions include applying and releasing the electronic calipers, reading and clearing fault codes, and an LED light to indicate power and parking braking system status.

Doing A Complete Brake Job
Asbestos still a hazard
Brake Pads: Choosing the Best Brake Lining Materials
Brake Rotors
More on Brake Rotor Service
Servicing Brake Hydraulics
Drum Brake Service
Drum Brake Wheel Cylinder Inspection & Service
Brake Fluid: A Hot Topic

Adapted from an article written by Larry Carley for Brake & Front End magazine

 

Back to Brake   |    Back to Info Main Page

Post your Comment
  - no <, >, [ or ] tags will go through. URL will be converted to link

Total messages: 0